Shilin Technology Co., Ltd.

Search for what you are looking for

Enterprise news

/NEWS

How can the noise from the motor be reduced?

Date:2025-06-14 作者:Shilin Technology Co., Ltd. 点击次数:196

Summary:The air gap between the stator and rotor of the motor is very small, w...

1. The air gap between the stator and rotor of the motor is very small, which easily causes the stator and rotor to collide with each other.

In medium and small-sized motors, the air gap is generally 0.2mm to 1.5mm. When the air gap is large, a large excitation current is required, which affects the power factor of the motor; when the air gap is too small, the rotor may experience friction or collision. Generally, due to severe deviations of the bearings and wear and deformation of the end cover inner hole, the three components of the frame, end cover, and rotor will have different axes, causing scuffing, which easily leads to overheating of the motor and even burning. If the bearings are worn, they should be replaced in time. For the end cover, it can be replaced or plated. A simple treatment method is to insert a sleeve into the end cover.

2. Abnormal vibration or noise of the motor can easily cause overheating of the motor.

This situation belongs to the vibration caused by the motor itself. It is mostly due to poor rotor dynamic balance, poor bearings, bent rotor shaft, different axes of the end cover, frame, and rotor, loose fasteners, or uneven installation of the base or improper installation of the motor. It may also be transmitted from the mechanical end. It should be addressed according to the specific situation.

3. If the bearing works abnormally, it will definitely cause the motor to overheat.

Whether the bearing works normally can be judged by auditory and temperature experience. The temperature of the bearing can be detected by hand or a thermometer to determine if it is within the normal range; or a listening rod (copper rod) can be touched to the bearing box. If there is a knocking sound, it indicates that one or several balls may have been crushed. If there is a hissing sound, it means that the lubricating oil of the bearing is insufficient. The motor should be replaced with lubricating grease after running for 3,000 to 5,000 hours.

4. The power voltage is too high, the excitation current increases, and the motor overheats excessively.

An excessively high voltage will endanger the insulation of the motor, making it prone to breakdown. When the power voltage is too low, the electromagnetic torque will decrease. If the load torque does not decrease, the rotor speed is too low, and the increase in slip rate will cause the motor to overload and overheat, and prolonged overloading will affect the motor's lifespan. When the three-phase voltage is asymmetrical, that is, one phase voltage is too high or too low, it will cause an excessive current in a certain phase or two phases, resulting in local heating, aging of the insulation, and damaging the motor. A broken circuit refers to the fault where the stator or rotor of the motor is broken or burned out. Whether it is a short circuit of the winding or a break will cause the motor to overheat and even burn out. Therefore, when such a situation occurs, the motor must be stopped immediately for handling.

5. Short circuit of the winding, inter-turn short circuit, phase-to-phase short circuit, and winding break

When the insulation between two adjacent conductors of the winding is damaged, the two conductors will collide, which is called a winding short circuit. If the short circuit occurs in the same winding, it is called an inter-turn short circuit. If the short circuit occurs between two-phase windings, it is called a phase-to-phase short circuit. Regardless of which type, it will cause an increase in current in one or two phases, resulting in local heating, aging of the insulation, and damaging the motor. A broken circuit refers to the fault where the stator or rotor winding of the motor is broken or burned out. Whether it is a short circuit or break, it may cause the motor to overheat and even burn out. Therefore, when such a situation occurs, the motor must be stopped immediately for handling.

6. Material leakage into the motor interior reduces the insulation of the motor, causing the allowable temperature rise of the motor to decrease.

If solid materials or dust enter the motor interior through the terminal box, they will reach the air gap between the stator and rotor of the motor, causing the motor to scuff and until the insulation of the winding is worn out, damaging the motor or making it obsolete. If liquids and gas media leak into the motor interior, it will directly cause the insulation of the motor to decrease and trip.


分享到: